Snorkel S3246 CE Bedienungsanleitung PDF herunterladen (Seite 37)

S2646/S3246 – 0410063EE 33

3. Place the battery disconnect switch in the on posi-

tion.

Lower Controls

The lower controls override the upper controls. This means

that the lower controls may be used to operate the plat-

form regardless of the position of the upper controls emer-

gency stop button.

Only the platform raise and lower functions may be oper-

ated from the lower controls. The lower controls may be

used for initial set up of the aerial platform and for posi-

tioning the platform while testing or during inspection.

Use the following procedure to raise or lower the platform

using the lower controls.

1. Pull the emergency stop button outward (refer to Fig-

ure 9.1).

Figure 9.1 – Lower Controls

2. Insert the key into the control selector switch and

turn the switch to the lower controls position.

3. Hold the platform raise/lower toggle switch up to raise

the platform and down to lower it.

4. Release the toggle switch to stop movement.

Upper Controls

The upper controls (refer to Figure 9.2) may be used for

driving the aerial platform and positioning the platform

while on the job.

Before operating from the upper controls, properly set up

the aerial platform as described under Preparing for Op-

eration. Use the following procedure to operate the aerial

platform from the upper controls.

1. From the lower controls, insert the key into the con-

trol selector switch and turn the switch to the lower

controls position.

Chapter 9 – Operation

The aerial platform may be operated from either the lower

or upper controls.

ADanger

The aerial platform is not electrically insulated.

Death or serious injury will result from contact with,

or inadequate clearance from, an energized con-

ductor. Do not go closer than the minimum safe ap-

proach distance as defined by ANSI or national

safety regulations.

Pinch points may exist between moving compo-

nents. Death or serious injury will result from be-

coming trapped between components, buildings,

structures, or other obstacles. Make sure there is

sufficient clearance around the machine before

moving the chassis or platform. Allow sufficient room

and time to stop movement to avoid contact with

structures or other hazards.

The aerial platform can tip over if it becomes un-

stable. Death or serious injury will result from a tip-

over accident. Operate the aerial platform on a firm,

flat, level surface. Avoid travel speeds and/or rough

terrain that could cause sudden changes in platform

position. Do not drive or position the aerial platform

for elevated use near any drop-off, hole, slope, soft

or uneven ground, or other tip-over hazard. Do not

raise the platform in wind speeds above 12.5 m/s

(28 mph).

The platform rated work load is the total weight of the

personnel and equipment that may be lifted in the plat-

form. The work loads are stated on the platform rating

placard mounted at the rear of the platform.

ADanger

The aerial platform can tip over if it becomes un-

stable. Death or serious injury will result from a tip-

over accident. Do not exceed the capacity values

indicated on the platform rating placard.

Capacity values indicate the rated lifting capacity and do

not indicate aerial platform stability.

The operator bears ultimate responsibility for ensuring

that the aerial platform is properly set up for the particular

conditions encountered.

Preparing for Operation

Make certain the batteries are charged and the charger

is unplugged before operating the aerial platform. Use

the following procedure to prepare the aerial platform for

operation.

1. Perform a prestart inspection (refer to as Chapter 8).

2. Close and latch the battery and hydraulic trays.

Emergency

Stop Button

Platform Raise/Lower Switch

Control Selector Switch

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare

Snorkel S3246 CE Bedienungsanleitung Seite 37

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Spezialmaschinen Snorkel S3246 CE